Log in
Forum » Italy
Topic

Low emitting material- General Emission Evaluation

NC-v4 EQc2: Low emitting materials
posted by Antonio Saccardi on Oct 3, 2019, 10:42 am

Dear all

I'd need your comment about "Low Emitting Material credit, General Emission Evaluation". 

Regarding the recognized schemes accepted for projects outside the United States,...

Last reply: Raymond Salfiti, Oct 21, 2020, 10:50 am

SCAQMD 443.1 VOC content

NC-v4 EQc2: Low emitting materials
posted by Nativa Architecture on Oct 6, 2020, 9:22 am

Dear all, We have a product tested with the SCADMQ 443.1 rule with a...

Last reply: Reinhard Oppl, Oct 7, 2020, 8:33 am

Bathroom and deposit cooling

Healthcare-v2009 EAp2: Minimum Energy Performance
posted by Davide Liviero on Oct 7, 2020, 4:00 am

Hello everyone,

I am simulating a 6-floor, 50 000-square-meter hospital and I am struggling to understand how to behave with some zones. As far as I understood bathrooms and deposits are...

Letter of commitment

CS-v4 EAp3: Building-level energy metering
posted by Alessandro Zuanon on Sep 29, 2020, 4:20 am

Hi,

is it possible to submit a unique letter of commitment for building level energy metering and building level water metering?

Thanks,

Alessandro

Last reply: Marcus Sheffer, Oct 5, 2020, 12:39 pm

Number of steps per hour

Healthcare-v2009 EAp2: Minimum Energy Performance
posted by Davide Liviero on Sep 17, 2020, 8:10 am

Hello everyone,

I am looking for a way to speed up the simulation of a building. I found that a possible solution is to decrease the number of time steps per hour. Is it possible to set it...

Dividing large building into smaller ones

Healthcare-v2009 EAp2: Minimum Energy Performance
posted by Davide Liviero on Sep 15, 2020, 6:20 am

Hello everyone,

I am modelling a 60 000 m2 hospital using Design Builder. Unfortunately, the simulation of the whole building is extremely long, requiring up to a whole week. As a solution...

System 3 Heating source

NC-v4.1 EAp2: Minimum Energy Performance
posted by Davide Liviero on Sep 3, 2020, 8:49 am

Hello everyone,

I am creating the baseline model for an office and have been suggested to use System 3 as HVAC sytem template for it. Since in the proposed model I use electricity as...

Last reply: Davide Liviero, Sep 4, 2020, 11:10 am

Target Finder outside the US

NC-v4.1 EAp2: Minimum Energy Performance
posted by Davide Liviero on Jul 29, 2020, 5:52 am

Hello everyone,

I ahve read that for LEED v4 BD+C Target Finder results are not required for projects outside the USA. Is this aspect still valid for LEED v4.1?

Thank you in advance...

Last reply: Marcus Sheffer, Jul 29, 2020, 9:35 am

Campus approach: CHP modeling (LEED v4.1 + ASHRAE 90.1-2016)

NC-v4.1 EAp2: Minimum Energy Performance
posted by Alessandro Zuanon on Jul 24, 2020, 7:34 am

Hi,

the project regards a campus (multiple buildings) served by a trigeneration plant (plant producing electricity, heat and chilled water). LEED versione is v4.1. 

...

Last reply: Marcus Sheffer, Jul 24, 2020, 2:25 pm

EAp3 and WEp3 Third Party Source VS USGBC Approved Data Template

LEED v4.1 Discussion Forum
posted by Davide Liviero on Jul 23, 2020, 5:06 am

Hello everyone,

I am working on LEED v4.1 BD+C Credit EAp3 (but the problem applies also to WEp3) and I am struggling to understand what the USGBC considers as approved data template....