Energy type ratio matching in baseline vs proposed
NC-v4.1 EAc2:Optimize Energy Performanceposted by William Pichon-Roy on
Hi,
Energy type ratio matching in baseline vs proposed
NC-v4.1 EAc2:Optimize Energy Performanceposted by William Pichon-Roy on
Hi,
Any initial findings regarding Project Appendix G performance under v4.1 compared to v4 (or even v3)?
NC-v4.1 EAc2:Optimize Energy Performanceposted by Joanna Switzer on
Hi all,
Clubhouse Building Type? Public Assembly or Non-Residential?
NC-v4.1 EAc2:Optimize Energy Performanceposted by Junaid Mujahid on
A clubhouse project with amenities including: Gymnasium, Yoga/Aerobic Studios, Party Hall, Dining Hall, Lounge, Small Retail Stores, Prayer Rooms, Basement Parking should be categorised under which
Infiltration rate @ 75 Pa (ASHRAE 2016) vs. 4 Pa / 50 Pa (Design Builder Software)
NC-v4.1 EAc2:Optimize Energy Performanceposted by Ziad Zeitoun on
Hello,
ASHRAE 2016 specifies the infiltration rate of the building at 75 Pascals (2.03 L/s.m²).
Porch lighting included in building energy model?
NC-v4.1 EAc2:Optimize Energy Performanceposted by Rachel Novick on
Our building has a large open-air porch that we use for parties. It has lights and ceiling fans.
environmental attributes (e.g. REC’s) retained
NC-v4.1 EAc2:Optimize Energy Performanceposted by Martin Maribo on
Can the purchase of environmental attributes be used to improve the Cost PCI points?
Carbon emission for Electrical Energy and Natural gas
NC-v4.1 EAc2:Optimize Energy Performanceposted by SAMY Chamy on
Dear Concern
Our project is located in Bangladesh and we are looking for carbon emissions per unit of electricity production and 1 m3 of natural gas usage.
v4.1, and Photovoltaic VE
NC-v4.1 EAc2:Optimize Energy Performanceposted by on
We are working on a warehouse in Sunnyvale, CA. We are confused with the results from the spreadsheet (v3), since we investigated removing the PV array, as a VE measure. Site Energy, Co
Off Site Power Purchase Agreement to Claim Saving ??
NC-v4.1 EAc2:Optimize Energy Performanceposted by SAMY Chamy on
Dear Concern:-
Has LEED provided any incentive for electrifying buildings in areas with clean electrical grids?
NC-v4.1 EAc2:Optimize Energy Performanceposted by Tim Nabholz on
Hi there,
EAc2 option question and PCI calculation
NC-v4.1 EAc2:Optimize Energy Performanceposted by Andrew Shaw on
Hello everyone,
Calculation in relation to the basic model
NC-v4.1 EAc2:Optimize Energy Performanceposted by Léanna Chérot on
Hello,
Option 2: New Building Institute Multifamily Guide under the LEEDv4.1 Residential Multifamily
NC-v4.1 EAc2:Optimize Energy Performanceposted by Anna Korinkova on
Hi,
Energy Model - Alternative compliance for LEED V4.1 BD+C
NC-v4.1 EAc2:Optimize Energy Performanceposted by Amal Venugopal on
Hi All,
Analyzing efficiency measures in addition to those in IP Credit: Integrative Process
NC-v4.1 EAc2:Optimize Energy Performanceposted by Mark Benson on
The Reference Guide for this credit in both LEED v4 and v4.1 say "Analyze efficiency measures during the design process and account for the results in design decision making." However, the fo
Mix coefficients from the International Energy Agency CO2 Emissions from Fuel Combustion 2017 report
NC-v4.1 EAc2:Optimize Energy Performanceposted by Dang Thi on
We have a project to persue LEED ZERO Carbon.
Bollard lighting on a recreational path
NC-v4.1 EAc2:Optimize Energy Performanceposted by Randi Meredith on
My town is proposing to install lighting along a partially wooded Rails-to-Trails path. Looking for specific recommendations for adequate lighting using bollards or something similar.
Consiterations -Equation PCI below PCIt
NC-v4.1 EAc2:Optimize Energy Performanceposted by Konstantina Kalliakoudi on
Dear Leedusers,
Please Confirm that the equation for “project percent improvement PCI below PCIt “ as mentioned at the credit is following :
[( PCIt- PCI)/ PCIt ]*100 (1)