See all forum discussions about NC-2009 EAp2
 Subscribe to new posts about NC-2009 EAp2 Post a new question aboutNC-2009 EAp2
See LEEDuser’s guidance on NC-2009 EAp2»
FAQs about EAp2 :

For a project outside the U.S., how do I determine the Target Finder score?

Do hotel rooms need automatic light shut-off control?

How commonly are the 90.1 mandatory compliance forms submitted as part of EAp2/EAc1?

The Section 9 space-by-space method does not include residential space types. What should I use?

Can the Passive House Planning Package (PHPP) be used to energy model for LEED?

Is it acceptable to model a split-type AC with inverter technology compressor as a heat pump, like modeling VRF?

Can the Trace 700 'LEED Energy Performance Summary Report' by uploaded to LEED Online in lieu of the Section 1.4 tables spreadsheet?

A portion of our building envelope is historic. Can we exclude it from our model?

Which baseline HVAC system do I use if my building has no heating or air conditioning?

For an existing building, do I need to rotate the model?

Our project has a diesel backup generator. Should we include it in our energy model?

Our project has a large process load—75%. Despite our efforts to make an efficient HVAC design, the cost savings are minimal. What can we do to earn this prerequisite and be eligible for LEED certification? Is there any flexibility in how we model the p

Can SHGC be higher in the proposed than in the baseline model?

Our process load is higher than 25%. Do we have to justify that?

Do I need to justify the electrical and fuel rates I am using in my model?

Our local code references ASHRAE 90.1-2010. Should I use that for my documentation, or 90.1-2007?

Can I claim exterior lighting savings for canopy lighting even though a baseline model cannot include shading elements?

The project is built on a site with existing exterior lighting installed. How should this be accounted for?

Can mezzanines open to floors below be excluded from the energy model?

How do I provide a zip code for an international location?

View answers »

Forum discussion

NC-2009 EAp2:Minimum Energy Performance

4 point mandatory minimum

Recently an addenda was published to refer that "for projects that register after XX/XX/XX and are subject to the four point mandatory minimum, demonstrate an 18% improvement in the proposed building performance rating for new buildings". (http://www.usgbc.org/sites/default/files/LEED%202009%20energy%20update%20-%20redline%20150901.pdf) Has this requirement been enforced already or is it to be enforced in the future?

0
Post a reply

You rely on LEEDuser. Can we rely on you?

LEEDuser is supported by our premium members, not by advertisers.

Go premium for $15.95  »

Profile picture for user sheffer
Marcus Sheffer
LEED Fellow
7group / Energy Opportunities
LEEDuser Expert
4454 thumbs up

Tue, 10/13/2015 - 14:12

This change has been proposed and not yet enacted. This is part of how LEED develops and changes. Substantial changes like this are sent out to the membership for public comment and then ultimately balloted by the membership. If it is approved they will enter a registration date when it takes effect. Any projects registered before that will be grandfathered.

Wed, 12/23/2015 - 18:27

Marcus, is there an estimated date after which any registered projects should comply with the proposed energy update (if approved)? Would that be January 8th, 2016?

Wed, 12/23/2015 - 18:40

Is there an estimated date after which any project that is registered should comply with the proposed energy update? Would this date be the January 8th, 2016?
Profile picture for user sheffer
Marcus Sheffer
LEED Fellow
7group / Energy Opportunities
LEEDuser Expert
4454 thumbs up

Wed, 12/23/2015 - 18:47

I have not seen an estimated date yet. I think this is where we are in the process - http://www.usgbc.org/articles/leed-2009-energy-update%E2%80%94voter-registration-open-until-january-8

Add new comment

To post a comment, you need to register for a LEEDuser Basic membership (free) or login to your existing profile.