Log in

Search form

Forum
Topic

Can't use LEED 2009 MF sections for an NC 2.2 project.

General forums
posted by Nadav Malin on Sep 23, 2010, 2:42 pm

Hi Christopher,
The rules say that you're NOT allowed to use the LEED 2009 guidelines for which materials to include/exclude in an NC 2.2 project. To be safe you should just include the MF...

Last reply: Tim Crowley, Nov 29, 2011, 1:38 pm

Re: Community development project certification

General forums
posted by David Posada on Nov 29, 2011, 1:21 pm

You might try posting your question at the forum topic for LEED-ND projects:
http://www.leeduser.com/...

Last reply: David Posada, Nov 29, 2011, 1:30 pm

Owner Agent required information

NC-2009 EAc2: On-Site Renewable Energy
posted by Francisco Villela on Nov 29, 2011, 10:54 am

Marcus,
I am looking at the on-line form for EAc2 On-Site Renewable Energy. (LEED 2009 for New Construction) The asterisk occurs after each of two Required Signatory boxes. Path selected...

Last reply: Marcus Sheffer, Nov 29, 2011, 11:56 am

Sealants and gaskets

NC-2009 IEQc4.2: Low-emitting materials - paints and coatings
posted by ruffina thilakaratne on Nov 29, 2011, 1:49 am

Tristan Roberts Representative Vermont House of Representatives LEEDuser Expert 11474 thumbs up November 29, 2011- 10:30 am Ruffina, this credit covers things that are applied on site—usually wet-applied. So gaskets would not be covered, and usually glazing is made off-site. Sealants are covered under IEQc4.1, so please post your questions about those under that forum. Log in or register to post comments ...

Last reply: Tristan Roberts, Nov 29, 2011, 10:30 am

Commissioning innovation point

CS-2009 EAc3: Enhanced Commissioning
posted by Magnus Stagnäs on Nov 29, 2011, 2:26 am

The reference guide states that CS projects requiring both fundamental and enhanced...

Last reply: Chris Ladner, Nov 29, 2011, 8:40 am

Interpretation doubt

EBOM-2009 EAc3.2: Performance measurement - system-level metering
posted by Carolina Vergnano on Nov 29, 2011, 5:55 am

Hello,
I've got a doubt about the time that we should develop the breakdown of energy.
The guide says: "This analysis of major energy-use categories must have been conducted within 2...

Last reply: Christopher Schaffner, Nov 29, 2011, 6:40 am

Exterior Lighting- LPD

CI-2009 EAc1.1: Optimize energy performance - lighting power
posted by Simon Sue on Nov 23, 2011, 3:48 am

We have a retail banking project. the building is 2 stories high + a roof top and was renovated. We installed a roof garden on it. we also install light fixture surrounding the roof garden....

Last reply: Glenn Heinmiller, Nov 28, 2011, 9:43 pm

Definition of hard-lid ceiling?

NC-2009 IEQc5: Indoor Chemical and Pollutant Source Control
posted by Renee Shirey on Nov 28, 2011, 5:30 pm

I have a situation where I cannot eliminate a sloped acoustic ceiling with a gyp ceiling, and the walls do not go up to the deck (they go to the underside of trusses). To enclose the room, I...

Last reply: Allison Beer McKenzie, Nov 28, 2011, 6:43 pm

Applying steel primer

NC-2009 IEQc4.2: Low-emitting materials - paints and coatings
posted by Michael Esposito on Jan 21, 2011, 8:13 pm

I have a steel fabricator applying a primer (grey) to the bar joists and steel for my project at thier facility. Do they still need to comply with the...

Last reply: Roberto Meza, Nov 28, 2011, 6:02 pm

Water Calculations for Landscape Irrigation

LEED for Homes (LEED-H) Forum
posted by Loretta Newcomer on Nov 28, 2011, 5:43 pm

I don't really have a question at this point. We have completed our project and submitted the paperwork; however, I would like to voice my frustration over the water calculation tool. I feel...