Log in
Forum » Middle East

Roof Water Feature

NC-v4 SSc5: Heat Island Reduction
posted by Omer Moltay on May 5, 2017, 6:49 am

Dear All,
My project is a museum building. The building roof is thick with water. So, project building roof have pool and observation terrace. Should it be counted as a reflective? Do I...

Last reply: Tristan Roberts, Aug 26, 2017, 8:20 am

LEED CI v3- Ofice- Energy Model. Please Advise

CI-2009 EAc1.3: Optimize energy performance - HVAC
posted by Nikhil Kumar on Aug 14, 2017, 7:29 am

I am doing Energy Model for LEED CI Project under V3 2009 Rating System. The project is G+M+3 Floors. Our tenant spaces are located in 1st Floor. Tenant’s spaces are conditioned by...

Last reply: Marcus Sheffer, Aug 23, 2017, 2:08 pm

Future-proofing LEED certification- Iran

General forums
posted by Meike Borchers on Apr 19, 2017, 4:21 am

I have a slightly different question in regarding to certifiable projects. One of our clients is keen to get a project in Iran LEED certified, however for political reasons it is not currently...

Last reply: Tristan Roberts, Aug 10, 2017, 4:04 pm

Powder products mixed with water on site application

NC-2009 IEQc4.1: Low-emitting materials - adhesives and sealants
posted by Ranya Metwalli Shields on Aug 1, 2017, 5:45 am

We are pursuing Credit IEQc4.1 in LEED NC v2009 for low emitting adhesives and...

Last reply: Ranya Metwalli Shields, Aug 7, 2017, 7:13 am

Multiple Metro Stations

LEED Rating System Selection
posted by MERVE AYGENC on Jul 18, 2017, 3:58 am

Dear all! I need some help in deciding the registration type of multiple metro stations. There are 11 stations to be certified and I cannot decide whether all of them should be registered as...

Last reply: Puneet Mital, Jul 30, 2017, 9:25 am

Applicability within campus boundary limits

NC-v4 SSp1: Construction Activity Pollution Prevention
posted by Samer Alhmdan on Jul 25, 2017, 2:59 am

I have multiple buildings within a campus, do we need to implement this prerequisite within the whole campus boundaries, or only within buildings LEED boundaries, noting that there...

Last reply: Trista Little, Jul 25, 2017, 6:47 pm

Data Sheet or Laboratory test report?

NC-v4 SSc5: Heat Island Reduction
posted by Samer Alhmdan on Jul 20, 2017, 8:46 am


Do we need a laboratory test report to substantiate the...

Last reply: Trista Little, Jul 20, 2017, 12:37 pm

Waste Receipts

NC-2009 MRc2: Construction Waste Management
posted by Rashed Al Nasa'a on Jul 13, 2017, 8:29 am

The contractor on our project has established a weighing station for trucks and vehicles within the project boundary and is planning to use it to measure the amount of diverted waste for MRc2....

Last reply: Michelle Reott, Jul 17, 2017, 11:34 am

PV panels on Roof

CS-v4 SSc5: Heat Island Reduction
posted by Andrea Tirao on Jul 6, 2017, 3:12 am

Our project has parking on basement, GF+1F office spaces, then roof is covered almost entirely of PV panels. Having the above conditions, we are initially assessing if we can either...

Last reply: Summer Minchew, Jul 12, 2017, 10:04 am

Proposed case outside airflow rates

NC-2009 EAp2: Minimum Energy Performance
posted by Cagril Comert on Jul 11, 2017, 11:08 am

Marcus Sheffer LEED Fellow 7group / Energy Opportunities LEEDuser Expert 5530 thumbs up July 11, 2017- 11:54 am How you model this could vary depending on the software you are using. In some software you need to create a dummy zone. For software specific questions usually the best place to try is either customer support (if it exists) or one of the discussion groups. There are several at onebuilding.org and http://energy-models.com/forum Log in or register to post comments ...

Last reply: Marcus Sheffer, Jul 11, 2017, 11:54 am